Edmunds Answers questions

Fuel pump relay not working, no spark, no fuel injectors. Ford F-150.

bronco71 — Tue, 05 May 2009 20:17:24 GMT

My truck just quit. In checking for troubles, I found that the fuel pump relay does not stay closed. It pulls in for about 1-2 seconds when the key is first turned on, then it opens.

It will close and stay energized if I ground the #6 test port on the ECC, and I get gasoline pressure at the pressure test port.

I do not have spark to the plugs, but do have power (12 vdc) to the coil. I called a supply house and got the ohm specs for the coil and it is within the range they gave me.

Where do I go from here?

what size length thread is the return trans line fitting at rad. on99 f150 4.6 4x4 4r7ow

beanzoid — Thu, 17 Jan 2008 22:59:17 GMT

am installing hayden trans. cooler and fitting that came with kit is too short. i want to run steel lines from new correct fitting to cooler & back up to original return line with as little rubber hose as possible thank you.

I have a 2000 F150 XL and most of the time the analog indicators do not come on for some time.

rssmit3 — Mon, 21 Jan 2008 09:45:24 GMT

My 2002 F150 dash indicators, MPH, Tach, Fuel, Oil, etc analog indicators/gauges do not come on immediately when the ignition is turned on. Sometimes it takes them over an hour to activate. Seperately, the odometer does not indicate immediately all the time either, but it is collecting the miles data as it does show additional miles when it finally comes on.

Anyone have a similiar problem and have a resolution?

1990 f150 4x4 problems

srghntr — Wed, 23 Jan 2008 23:37:25 GMT

while driving on 2 wheel drive for some reason or another my transmission switches to a nutural mode, I can put it back to drive by playing with my 4 wheel drive shift stick but i struggle to put it back in drive. I learn by putting foward preassure in the 4 wheel drive stick I dont have any problems. when I put it on 4 wheel drive the front wheels will not lock up but the trucks acts like is low 4 wheel drive but wheels are not locked
thanks with any info

2004 f150 4x4 sc whining sound in transfer case. mileage is 50,000 miles??

rocky04 — Mon, 04 Feb 2008 13:28:46 GMT

whining sound on accel and decel

how to remove pitman shaft seal on 1998 f-150

pazmustang — Fri, 15 Feb 2008 08:28:19 GMT

there is no snap ring holding in seal, what is the best way to remove this seal.

1991 f-150 5.0 no adjustment to reduce 1200 rpm in park need to be at 750 to set timing how do i lower idle speed

tspiro — Sun, 17 Feb 2008 09:57:03 GMT

need to set timing engine is running very high idle with no adjustment i know its electrically controlled how do i reduce idle from 1200 to 750 rpm. f-150-5.0 litre

still- f-150 idle running high at 1200 rpm

tspiro — Mon, 18 Feb 2008 08:47:54 GMT

my friend i have disconected the wire from the controler, and the idle stil stayed the same 1200 rpm. i also looked for broken hoses, and i dont here any leakage. there is another senser on the bottom of the thottle body could that be our problem.

how much is front end work for 99' Ford f-150

woffa — Sun, 24 Feb 2008 06:53:55 GMT

looking to have complete idle bar and u/v joits and whatever else needs to be done to stop front end from banging? any Idea of cost for this type of work.. thanks

My 2001 Ford F150 4wd auto. suddenly stopped going in reverse and now is slipping in drive, what should I do?

marhenke — Sun, 24 Feb 2008 11:54:17 GMT

I was driving around my property yesterday and went to backup, put the trans in reverse and nothing happened. It would go in drive but acted like it was in neutral when I selected "R". I got on the road and it started slipping in drive so I pulled it over into a parking lot where it now sits.

Do you know where the speed sensor is on a 96 Ford F-150?

bama1979 — Tue, 04 Mar 2008 16:34:28 GMT

I got a diagnostic scan done at Advance auto parts cause my transmission has been shifting rough and it shifts at a much higher RPM now. Plus my speedometer quit working along with my odometer. But a trouble code I got was this-
P0500 Vehicle Speed Sensor A Malfunction

I don't know a whole lot about cars. I just have general knowledge. But I just need to know if this is something I can check/replace on my own, because I can't afford to put my truck in the shop right now.
I would really appreciate any info you could give me.
Thanks,
Jeremy

I have an 2001 Ford F-150, do I need to bleed the brake after changing the brake pads on the rear ?

thompc3 — Sat, 08 Mar 2008 10:23:17 GMT

My brake pads are worn out.

Where can I buy used or cheap custom rims online for 2001 Ford F-150?

thompc3 — Thu, 20 Mar 2008 22:31:48 GMT

chrome

Ford F-150 steering column replacement. Do you need to take off the rod that connects the transmission linkage to the column?

shloop69 — Sun, 23 Mar 2008 07:43:01 GMT

help

2002 Ford F-150 power steering pump

rzajdel — Thu, 27 Mar 2008 22:09:40 GMT

Is it best to have a repair shop replace my power steering pump on my 2002 f150 4.2 liter,or can I replace it and how much trouble will it be

How tight should a front axle nut be on a 2000 Ford F-150 front hub assembly?

scottmon — Sun, 30 Mar 2008 15:37:10 GMT

I'm assuming that I tighten the nut and then back it off a bit before putting the cotter key in, but i am not sure how much.

How to change out rear leak springs shackle on 2001 Ford F-150?

thompc3 — Mon, 31 Mar 2008 22:05:58 GMT

2001 ford f-150

What size are the rear brake lines on a1997 Ford F-150 4x4?

pathco41 — Sun, 06 Apr 2008 19:36:39 GMT

1997 ford

What should the timing be for a 1993 Ford F-150 4x4 with a 5.0 engine be set at? We've heard 10/8 btdc and 12 atdc.

got2know — Sat, 26 Apr 2008 14:43:09 GMT

Hi
Help please:
(truck has just over 93,000 miles)

3 weeks ago my husband's truck starting running rough especially after it would rain. He did all the usual pm stuff with the plugs and wires. It still did the same thing. Since then he's replaced the coil, ignition switch, found a bad wire, changed the lock cylindar (he was having problems with that before and figured better change it)and the stator. Then we found out that the starter had a bad cellunoide (have no idea if that's spelled right) so that's also been changed.

Right now we're trying to get the timing set correctly we were told that it should be 12 degrees after top dead center...that doesn't seem to be right yet. We've also heard 8 or 10 degrees btdc none of those seem right either.

One more thing though...I had to use the truck, and I really didn't notice the truck bucking when breaking. When it got up to around 49-60mph the truck would shake/buck really bad but it would be smoother above or below those speeds. I don't know it's all really strange to me, plus when you're just standing still like at a light/where ever the truck is having problems with idling - it sounds/feels like it wants to quit.

Any help would be appreciated. Thanks

How do I time a 300 v6 in a 1986 Ford F-150?

tyler88 — Fri, 09 May 2008 16:34:10 GMT

what position to put the crank and cam gears in to be in time.

Labor time for replacing 88 Ford F-150 steering column?

boo1165 — Sun, 13 Jul 2008 07:03:50 GMT

the labor guide for replacement of steering column

Help, is the salesmen being straight with me about my Ford F-150 towing ability?

want2go2 — Thu, 17 Jul 2008 22:37:52 GMT

Help me please>>> I took deliver on a 2008 Ford F150, supercab 5.4 V8 4 speed auto.I notice that on the invoice it has a axle ratio of 3.31. Called the salesman and he said that was good for towing. The truck is new and doesn't have any pep. I'll be towing a TT about 3800lbs My other truck had a 3.55 axle. The truck had no tow package but the said they would put a hitch and 7 pin electric connector. I checked the towing guid book and found only one 3.31 axle and that was for a 4.2L standard shift.
PLEASE try to answer ASAP so I can talk to ford before it's too late.. Kind Regards, Joe

What steering columns are interchangeable with a 1988 Ford F-150?

boo1165 — Sun, 27 Jul 2008 07:20:31 GMT

I bought a 88 f150 and the s.column is all messed up. It has tilt and automatic, the shifter is on the column.

How do I replace the front rubber wheel steering boot. Ford F-150.

dmains — Sun, 27 Jul 2008 18:07:14 GMT

It is the big rubber boot behind the front wheels. 1997 ford f150 4wd. I accidentally damaged it while replaceing the front shocks.

Brakes chatter as speed slows to stop. Problem occured suddenly. Ford F-150.

chiperu — Fri, 15 Aug 2008 20:58:14 GMT

'04 F150, 2X, 4 wheel ABS, brand new rotors and pads

95 Ford F-150 XL 2wd with air. Need correct tenssion idler pulley diagram and correct belt diagram. Also runs hot, no thermostat?

lesa3 — Sun, 07 Sep 2008 14:20:30 GMT

new power steering pump on, since then, it has broken the idler pulley that came with, auto parts assures me they are giving me the correct one, keeps slinging belt over ps pulley. idler pulley is align when belt is off. can you send me a diagram of the correct pulley's and also the correct part#'s for tension pulley and alternater, also a front view diagram?? Thanks also runs hot, no thermostat is in??? not circulating. angry nephew put instant coffee in ps, radiator, trans, causing ps to lock up with me and my 4 yr old son going around curve, please help
1995 f150 4.9 six, with air

What's included in Ford's F-150 preferred 508 package?

jjn49 — Sat, 27 Sep 2008 05:33:35 GMT

Dealer's Windows stickr on f150 Lariat list a preferred equipment PKG .508.
Also something called Lariat series. Trying to find out whatoptions are included in these packages. I susoect most are standard equipmnet for the Lariat just can't find it anywhere..Thanks

Jim

I just bought a new 2008 F150 XLT Crewcab with the Navigation system. What does the phone button do?

m2bord — Sat, 01 Nov 2008 16:31:18 GMT

I just bought this today and it's my 4th F150 since 1996.

I have a good understanding of the Sirius satellite and the other navigation features but I have no clue what the phone button does. So I asked the dealer and they don't know either. The manual says to consult with my "Ford Authorized Dealer" and if they don't know...then what?

How much grease do I use for 1997 Ford F-150 front hub assembly?

merlin1975 — Sun, 09 Nov 2008 12:26:42 GMT

trying to replace front hub assembly for first time, not sure how to, or how much grease to use... please help?

Does the '98 Ford F-150 with a4.7L develop the low end torque I need for pulling my 3000lb boat or is it more of a high end vehicle?

stayo — Thu, 20 Nov 2008 17:55:54 GMT

does the '98 F-150 w/4.7L develop the low end torque I need for pulling my 3000lb boat or is it more of a highend vehicle?

I have a 1985 Ford F-150 with a 351 small block. The choke sticks on it. Where would it be located?

85ford — Wed, 24 Dec 2008 11:52:46 GMT

its a carb. and when u give it gas some time it try 2 cut off

Any idea why my 1984 Ford F-150 revs up and down even at a steady 55 mph. Happens at all speeds, even idle.

jaynogo — Mon, 29 Dec 2008 12:48:25 GMT

my 1984 f 150 van v8 is a bear to start or should i say once started hard to keep running, that's probably the spring choke ? ? when it dose idle with a little pedal it revs up & down ( not a lot )it seems to do this most of the time even when i'm on the high way @ 50 - 60 mph with my foot perfectly still on the gas pedal. almost like bucking motion.HELP ITS DRIVING ME CRAZY Jay K.

How do I remove a broken off drain plug in the radiator in a Ford F-150? Drill the broken stub through into the radiator?

johnnymetal — Sun, 04 Jan 2009 13:51:40 GMT

re: broken off drain plug stem

2001 Ford F-150 4X4. Water leaking from exhaust.

chadc1314 — Tue, 20 Jan 2009 11:20:13 GMT

I noticed today that my truck is leaking a lot of water from the exhaust, so much that it looks to be leaking from the muffler as well. It hasn't rained or been in water in quite some time so we can rule that out, and it is a colorless and odorless liquid so I am assuming it is water. It only leaks when it is running, what gives?

Cause of Lower Ball Joint failure on 2008 Ford F-150?

benpowell — Sat, 31 Jan 2009 21:49:04 GMT

i have a 2008 f 150 with 47000 miles. Took it to repair shop today because one tire (inside driver's side) is severely cupped. They said i needed lower ball joint on driver side and that was unheard of on a truck that new. I was wondering as to possible causes of lower ball joint failure.

Oil capacity for a 1993 Ford F-150 XL 4.9L I6?

Coltwd — Sat, 07 Feb 2009 13:32:01 GMT

Doing an oil change and lost the owner's manual

My power steering only works turning to the left, what's wrong? Ford F-150.

dan150 — Mon, 09 Feb 2009 11:08:19 GMT

'89 f150 4x4. greased all steering rod ends. I don't want to spend money on a pump if the problem is in the box.

Does anyone know what it is or how to actually fix a vibration in my 2006 Ford F-150?

jake319904 — Sun, 08 Mar 2009 14:44:47 GMT

i have a 2006 F-150 W/ a 5.4L V8 it has a vibration at idle and a severe one while towing any thing. the fuel mileage also stinks.

Changing tires on 2005 Ford F-150 from 255/65R17 to 265/70R17. Will that present any problems?

rasbury — Wed, 25 Mar 2009 09:23:50 GMT

changing tires on 2005 F150 from 255/65R17 to 265/70R17 will that present any problems

Ford F-150 2006 XLT v6 2WD vibration at 65 to 75 mph. How do I fix it?

rzarin — Sat, 28 Mar 2009 15:34:49 GMT

Ford F-150 2006 v6 2WD. I have steering wheel vibration @ 65 to 75 mph. How can I fix it?

Where is the SYNC microphone on a 2009 Ford F-150?

andymeadows — Wed, 27 May 2009 10:36:09 GMT

I searched the owner's manual and cannot find the location of the microphone. I'm trying to tune the volume/microphone and wondering where the mic is located so I can test some various techniques to improve sound quality. My truck is a 2009 F150 SuperCrew.

Can a parked Ford F-150 be hit from the front hard enough to move it 16" without leaving skid marks?

elshue55 — Sun, 31 May 2009 13:29:52 GMT

The owner of an F-150 claims his truck was hit by one of our company vehicles while his was parked on the street. The owner of the F-150 says the impact was hard enough to move it back 16".

While the employee does not deny hitting the truck, the severity of the impact is in question. The employee denies the impact moved the truck at all. His basis for this claim is that there are no skid marks 16" in front of where the owner of the F-150 says the vehicle originated.

97 Ford F-150 4.2 tps checked out ok with volt meter and ohms. Loss of power when warm.

bobber4 — Tue, 02 Jun 2009 14:09:49 GMT

I disconnected the sensor and drove for a while no backfire, still drove about the same any other suggestions? Bobber

I have a 1997 Ford F-150 pickup with 144,00 miles on it. Does it qualify for the Clunker voucher program?

dknights1 — Fri, 12 Jun 2009 11:04:19 GMT

I have a 1997 F-150 Ford pickup truck with 144,00 miles on it. Does it qualify for the Clunker voucher program? If it does, how come it does not appear on the Edmunds.com eligible vehicle list when similar age and size GM and Chrysler pickups do. If it does not qualify, how come?

I need touch up paint for my 1992 Ford F-150. The code is DD. All I see on the paint sites is DB.

jlprid — Mon, 22 Jun 2009 19:39:29 GMT

Every site I can find only list the DB color code for the F150. I have triple checked the door panel code and it is DD, The truck has the original color. What's up with the code?

97 Ford F-150 4.2. Where do I put the engine girdles on main cap bearings, front or back stud? Told only need one but I have two.

weber50f150 — Mon, 20 Jul 2009 13:27:07 GMT

Rebuildding engine Ford 97 F 150. Got short block from machine shop. Bolts for main cap bearing in wrong place. Need to put girdle on but I did not see how it came off.

2005 Ford F-150 GTR 4x4.

healinrain — Fri, 21 Aug 2009 06:43:15 GMT

I'm in the market to purchase a 2005 F-150 GTR 4x4 that has crossed my path. I find no material on this pick up. Is it a NASCAR series or something else. It rocks my world. This thing is awesome. Let me know if anyone has info on it. Thanks, George

Where does the 3/16 id hose connect to? Ford F-150.

visionary8 — Thu, 10 Sep 2009 09:18:14 GMT

1985 Ford F-150 5.0 EFI V8 auto/trans without carburetor.

On top of the penlum,there are some vacuum hoses that branch out.

At the bottom of these hoses is a 3/16 id hose that curves around the front of the throttle body and,ends up on the passenger side fender well.That's how long the hose is.
I've been told it goes to the power booster,charcoal cannister,and the cruise control...no,no,and no! Where does it connect to?

With the engine running,the hose sucks in air,not out.
thanks,
Neil

1985 Ford F-150 5.0 EFI V8 automatic transmission without carburetor. PVC valve?

visionary8 — Thu, 10 Sep 2009 10:20:54 GMT

I have a "repair manual" that came with the truck,it's just a little booklet. There's a picture in the manual that,shows the PCV valve is behind the smog or polution pump but,the Ford dealer says it's under the penlum at the rear of the intake manifold!?

I cannot see behind the penlum because,it's to close to the firewall.

How can I see it,let alone replace it?

thanks,

Neil

Where is the EGR valve located on a 1985 Ford F-150 5.0 EFI V8, or is it not equiped with one?

visionary8 — Thu, 10 Sep 2009 10:45:34 GMT

1985 Ford F150 5.0 EFI V8 auto/trans 2wd without carburetor.

"If" there is a EGR valve on this pick up truck,where is it exactly located and,where does the vacuum hose from the EGR valve connect to?

thanks a lot,

Neil